ADSS Clamp Tension Set-manufacture,factory,supplier from China

Features of Transmission Line OPGW Tension SetA. the stress distribution is uniform and there can be no pressure focus factor, that can protect the optical cable well.B. beneath the concept of now not exceeding the lateral compression electricity of the optical cable, it has a greater grip at the optical cable and can resist more tension.C. the grip energy of the optical cable isn't always much less than: 90 5% of the last tensile energy (uts) of the optical cable, that is clearly suitable for the wishes of optical cable erection.

Spiral preformed tension clamp and ADSS single-layer tension clamp have similar functions as tension clamp. Spiral preformed tension clamps are mainly used for poles and towers with short spans of 50 to 200 meters, such as corners, tensions, and terminals.

Characteristics1) low wear: because of the big bar and short good sized clench conductor, the cord is tough to slide, the wear and tear might be minimum.2) save you loosening: the preformed has preserving elasticity, it make sure it not unfastened in long time;3) good corrosion-resistance characteristics: after antirust processing, the cord ensuring the sturdy corrosion resistance;4) clean set up: no unique equipment, the hand can installation quick and easy in locale, one person can finish.5) installation first-class warranty: no need the special training; it is able to be inspected by using

With the continuous growth of China's national economy as a whole and the influence of the reform of telecommunications system, the market demand for ADSS power optical cable has increased significantly, reaching 10 million core kilometers in 2001.In the 21st century, there were several situations at that time: (1) Domestic optical cable enterprises were affected by the "bubble" of optical network, and the telecom market shrank, and the supply exceeded demand.

1.extensive variety of applications, torsion resistance and pressure resistance, balanced torsion torque, company and tight locking, and huge adjustment variety. 2.put it at the telegraph pole, tighten and fix it. 3. the poles with diameters of one hundred seventy five-197mm can be adjusted. Pole clamp belt for cable garage bracket is manufactured from c201 stainless-steel, with width of 19mm, thickness of 0.7mm and duration from 1.2m to at least one.5m primarily based on exclusive pole.

The preformed suspension clamp is used for the connection of various wires such as ADSS optical cable and OPGW optical cable in the linear pole tower.

The tension clamp is deployed at a ordinary time. the current within the circuit is deployed from one end of the electricity supply, and the electrical putting gadget is deployed returned to the opposite end of the strength supply to form a closed circuit. if the present day circuit is blocked, the disconnection may arise due to some purpose. the modern-day within the circuit is not smooth, and the circuit does no longer form a closed loop. this is called an open circuit. therefore, all components need to be freed from hysteresis loss.

Identification and use of strain clamp specifications: According to the wire, the general strain clamp can be divided into two types, one is the wire strain clamp, and the other is the optical cable strain clamp. Their appearance is very different and can be easily distinguished.　　 The wire tension clamp is also called the bolt-type tension clamp (NLD-1). When in use, the vertical pressure of the U-shaped screw and the friction generated by the wavy slot of the wire clamp are used to fix the wire.

Tools/raw materials Aluminum alloy joint box Pre-twisted suspension clamp Optical cable down lead clamp Cable rack Tower fastener Cable hoop Whip and hammer Pre-twisted hardware1.Before installing the inner twisted wire, pass the outer twisted wire through the embedded ring and make it parallel to the optical cable, and mark the optical cable where the outer twisted wire is colored.2.Winding the first group of inner twisted wires on the optical cable; Align the second group of inner twisted wires with the first group of inner twisted wires, winding the s

Optical cable joint box, ADSS optical cable joint box, OPGW optical cable joint box, OPPC optical cable joint box Uses: Widely used in ADSS, OPGW special optical cable joints and the junction of different optical cables, and play a role in protecting optical cable joints. Features: 1.The metal splice box is made of aluminum alloy casting, which is especially suitable for the protection of optical cable joints under high-voltage electric fields. 2.The metal splice box overcomes the weakness of the plastic splice box, which is poor in anti-aging ability and short life under t

Mini-Bracket Mini Brackets are used for short and medium spans of ADSS fiber optic cable as well as Aerial Drop cables. Mini Brackets are sized to fit specific ADSS diameters. Standard Mini Brackets are employed with fitted bushings to provide a good support/groove fit and to prevent the support from damaging the cable. The bolted supports are supplied with aluminum captive bolts to simplify installation with no loose parts.

The pole clamp is suitable for connecting the anxiety suspension clamp and the electric pole. A big quantity of various varieties of hoops are wanted in overhead strains or whilst putting in pole accessories. it's miles especially easy to put in hoops on equal-diameter poles, just recognize the unique diameter. while installing a hoop on a tapered pole, if the hoop size is simply too massive, you want to insert iron pieces internal; if the ring is too small, the hoop and the telegraph pole cannot in shape together.