Bi-metal Connectors-manufacture,factory,supplier from China

(Total 24 Products for Bi-metal Connectors)
The bi-metal connector is designed to provide an effective corrosion barrier between the dissimilar metals aluminium and copper.The threads nuts and tapped holes is cut after galvanizing and well greased. All other threads is formed before galvanizing. Each PG is tightened  by two bolts with nuts and washers.
  Contacter maintenant
There are many types of cold-rolled steel strips and their applications are also very wide. In order to distinguish various chemical compositions and various purposes of strip steel, and to facilitate selection and use, it is necessary to understand the steel grade.The stainless steel strip is made by further cold rolling.
  Contacter maintenant
The protective armor rod is a metal wire that is spirally wound on the wire to increase the rigidity and vibration resistance of the wire at the winding position.
  Contacter maintenant
The JJ-3 insulation piercing clamp has a main line cross-section of 16-95mm, a branch cross-section of 1.5-10mm, an applicable voltage of 1KV, and a nominal current carrying capacity of 138. It has the characteristics of long service life, high conductivity, and firm wiring.Features: 1. Simple installation: puncture structure, no need to strip the wire, torque nut, constant puncture pressure.2. Thickened shell: Nylon material is used to ensure that it can bear enough pressure.3.
  Contacter maintenant
Rag bolts conforms with BS 1494, except that the bolts shall be 72mm long and they are supplied with M10 thread, coarse pitch, free fit.Each bolt is supplied with one full nut.Features:- Tensile strength: 352 N / mm2- Elongation (break): 33%- Code bending: 180°Measures:- Diameter: 10mm- Length: 72mm- Thickness of tube: 0.6mm- Unit weight: 21gramPackaging:Resistant cardboard box with the customer information in the visible part of the box. TECHNICAL SPECIFICATION: SpecificationLengthQuantity per cartonUnit weight gramWeight per carton(kg)10
  Contacter maintenant
Galvanized ball eyes is a ball head hanging ring with a protective layer. The characteristic of the ball head hanging ring is to avoid direct impact between the metal ball head and the insulator.Technical sheets: 
  Contacter maintenant
The JJC-2 piercing clamp is equipped with a tightening torque nut. The screws are treated with corrosion resistance. The torque nut makes installation easier, safer and faster. Its constant piercing pressure can ensure the cable connection to achieve the best electrical effect. The puncture has a waterproof function, and can withstand a voltage of 6kv in water without breakdown.
  Contacter maintenant
The JJ-3 insulation piercing clamp has a main line cross-section of 16-95mm, a branch cross-section of 1.5-10mm, an applicable voltage of 1KV, and a nominal current carrying capacity of 138. It has the characteristics of long service life, high conductivity, and firm wiring. Features:1. Simple installation: puncture structure, no need to strip the wire, torque nut, constant puncture pressure. 2. Thickened shell: Nylon material is used to ensure that it can bear enough pressure.3.
  Contacter maintenant
The JJC series of low-voltage cable piercing clamps use excellent insulation materials and sufficient materials, which greatly improves the stability of the product and has a long service life. The product models are complete in variety, stable in size and easy to match. It is used for the branch connection of insulated cables in building power distribution systems, the connection of low-voltage overhead insulated cables, the branch connection of low-voltage insulated incoming cables, and the street lamp power distribution system. Features:1. Main branch: 1.5-25sqmm2.
  Contacter maintenant
The JJC-2 piercing clamp is equipped with a tightening torque nut. The screws are treated with corrosion resistance. The torque nut makes installation easier, safer and faster. Its constant piercing pressure can ensure the cable connection to achieve the best electrical effect. The puncture has a waterproof function, and can withstand a voltage of 6kv in water without breakdown.
  Contacter maintenant
The ball eye is an iron circular device used to connect insulating suspension pieces. Forging of high-quality metal, in line with ISO production standards. The zinc layer is uniform, the surface is smooth, corrosion-resistant and rust-resistant, strong and durable, and has a long service life.
  Contacter maintenant
Applications 1.Tensile clamps for OPGW optical cables are mainly used to connect optical cables with a breaking strength of 160kN and below to tensile poles, corner poles and terminal poles. The complete set of OPGW optical cable strain clamp includes outer pre-twisted wires, inner pre-twisted wires, supporting connectors and grounding wires.
  Contacter maintenant
Universal pole bracket UPB is made of aluminum alloy with high mechanical strength. Its unique design has been engineered so to offer an universal pole hardware solution able to adapt to all cable installation configurations on wooden, concrete or metal poles.Features: Working load: 5KNUnit weight:220gCarton size: 420×280×230mmQuantity per carton : 50 piecesMaterial: aluminum alloyDelivery time: 10 daysDrawing: Packing: 50 pieces per carton 
  Contacter maintenant
The down-lead clamp for metal rods is used to fix ADSS on the rod. It is suitable for different cable diameters. It is convenient and reliable to install and has a wide adjustable range.1.Function: Fix the optical cable leading up or down on the pole tower to prevent it from shaking and avoid the optical cable from wearing. 2.Condition: The fiber optic cable line and the continuous poles on the first and end poles. 3.Method: usually install one every 1.5 meters.Technical specification table: 
  Contacter maintenant
The top tie are all designed in a spiral structure and include aluminum-clad steel wires. the central part of the energy distribution cable is fashioned in the factory, and its form may be matched with diverse insulators and wires.
  Contacter maintenant
Features: 1.The product has been treated with hot-dip galvanizing and has good outdoor anti-corrosion performance. 2.According to the requirements of different optical cables, products that ensure that the optical cable is smaller than the bending radius can be designed. 3.It is convenient to install the pole and tower, the installation is firm, and the optical cable can be well protected to avoid the optical cable from wearing. Purpose: It is used to place the surplus optical cable when the optical cable is connected.
  Contacter maintenant
Function: the anti-vibration part dampen wind vibration, consume or weaken the vibration energy generated by the laminar wind during the operation of the optical cable, and prevent the damage of the hardware and the optical cable. Purpose: Suitable for ADSS optical cable. Factors that cause vibration: wind force, wind speed, tension, span, wind direction, topography, landform, fiber optic cable structure, length, etc. Note: The installation position of the spiral damper on the tension clamp or the suspension clamp is the same.Specification required for different cable diameter r
  Contacter maintenant
Stay grips dead ends is the preformed wire type, minimum length is 600mm and finish is galvanized. Thimbles is used with guy grips to support wires through the stay rod eye. A combination of guy grips and pole top make offs is used.Installation image:
  Contacter maintenant
Down-lead clamps for rubber towers are used to fix the up and down or up of the optical cable on the tower so that it will not shake and avoid the optical cable from wearing. Features: 1.Wide range of application: It is suitable for skeleton type, layer stranded type, beam tube type armored and non-armored fiber optic cables, and is flexible in use. 2.
  Contacter maintenant
The self-supporting figure 8 optical cable clamp has a flat surface, special material and embedded design, which can well protect the cable. Its technology is superb: high-quality aluminum alloy material, rubber clamp block, reduce wear.
  Contacter maintenant
Structural features: 1.The anti-vibration rod will not cause the stress concentration of the wire, nor damage the wire, to avoid corrosion or arcing. 2.The spiral anti-vibration rod is composed of a short gripping section and a long damping section. 3.The gripping section can effectively hold the cable and firmly fix it on the cable.
  Contacter maintenant
Tie rods is supplied with four full nuts. The material of the rods is steel, strength grade designation 4.6 and meet the requirements for mechanical properties.
  Contacter maintenant
ADSS preformed tension set , single-layer twisted wire can be used below 200 meters; high-tension strain clamp, double-layer twisted wire can be used for spans above 200 meters. The technical parameters required for the quotation are: the diameter of the applied wire, the range of use, the tensile force and so on.Composition: inner rods, helical guy grip, thimble clevis, U shackle, extension ring, etc.Product parameter According to different needs, the configuration intensity is 70kNSn Model No.
  Contacter maintenant
The structure of the preformed armor rod and the short protective rod is simple. A set of pre-twisted wires form an empty tube, which generates a gripping force when wrapping the wire, thereby protecting the wire. The pre-twisted wire protection line is used for vibration protection and has been included in the hardware products.
  Contacter maintenant
Relate News
Power fittings are metal parts used to connect power transmission line towers, wires, lightning protection wires and insulators, or to protect wires, lightning protection wires, insulators, etc.    Basic requirements: Power fittings are generally made of cast steel and malleable cast iron. It is required that the circuit fittings should have sufficient mechanical strength, and the part of the fittings connecting the conductors should have good electrical properties.
The hoop is used to restore the metal strand or cord on the pole, and the pull is much like solving to the wall or other objects to tighten the steel strand. There are numerous styles of hoops, cable hoops, telegraph pole hoops, cable hoops, cable hoops, and stainless-steel hoops are extra usually used.Cement poles can be divided into rectangular, octagonal, i-formed, circular or a few different particular-common go-section poles in step with their cross-sections. amongst them, the extra generally used are spherical bolstered concrete poles.
Power fittings are accessories made of metal materials that are often used for power output. These accessories are of various types, and the shape and size of each part are different, but they play a very important role. Even very small parts will be indispensable, helping people to output electricity. Some of our common metal rings or metal clips, as well as connecting rings that can be connected to metal pipes, belong to the category of fittings.
Characteristics of PET Packing Tape(1) Sturdy tensile energy, not most effective has the tensile power of metal strip, but additionally has the ductility of effect resistance, that may ensure the transportation safety of merchandise. (2) Small elongation, elongation is most effective one-sixth of the polypropylene belt, can hold the anxiety for a long time. (3)Robust temperature resistance, melting point of 260 stages, a hundred and twenty degrees under the use of non-deformation. (4) Top security, no metal rust pollutants of the sure gadgets, vivid shade can be used for referen
Optical cable joint box, ADSS optical cable joint box, OPGW optical cable joint box, OPPC optical cable joint box Uses: Widely used in ADSS, OPGW special optical cable joints and the junction of different optical cables, and play a role in protecting optical cable joints. Features: 1.The metal splice box is made of aluminum alloy casting, which is especially suitable for the protection of optical cable joints under high-voltage electric fields. 2.The metal splice box overcomes the weakness of the plastic splice box, which is poor in anti-aging ability and short life under t
The tension clamp is deployed at a ordinary time. the current within the circuit is deployed from one end of the electricity supply, and the electrical putting gadget is deployed returned to the opposite end of the strength supply to form a closed circuit. if the present day circuit is blocked, the disconnection may arise due to some purpose. the modern-day within the circuit is not smooth, and the circuit does no longer form a closed loop. this is called an open circuit. therefore, all components need to be freed from hysteresis loss.
We finished the HDG angle cross arm and arranged shipment in May of 2019 to our customers from Tanzania. 
We clean our workshop on time and keep our workers workings in a clean, comfortable and organized place. 
After finishing products, before packing, we put our products in very tidy way so that the quantity never be shortage when customers received the items. 
Wonderful anti-pressure ability, accurate brief-circuit current ability ;Match with ordinary floor cord l undertake stainless-steel pipe production generation, the pipe is full of water-blocking off compounds, the application version can efficaciously protect the optical fiber ;Using stainless steel tube production technology, the tube filled with water-blocking compounds, can effectively protect the optical fiber;The utility model has the dual functions of a ground wire and a communication optical cable, and avoids the huge cost of repeated erection and maintenance;It is installed on the top
The standard plywood crates customized based on requirements of customers and loaded in the container.
Electricity is the most indispensable energy source in our lives. Without it, our lives will fall into a mess, and it is the high-voltage wires that ensure that the electric energy reaches our living places safely. In the past, when technology was not so advanced, wires were pulled from the sky to every household, so many small counties still have many cables between houses. In cities, more are buried underground, which can be more secure. However, in many heavy industrial areas, high-voltage wires still need to be passed through high-altitude.