Compression Repair Sleeve-manufacture,factory,supplier from China

(Total 24 Products for Compression Repair Sleeve)
The repair sleeve comprises of two pieces with a provision of seat for sliding of the keeper piece.
  Contacter maintenant
A compression type mid-span joint consists of the following parts:a. Aluminium alloy tube for aluminium alloy conductors.b.
  Contacter maintenant
Product characteristics:1.Easy and fast to use, single-tube construction, resistant to water and dirt2.Made of tin coated copper with high conductivity, they provide a strong and durable connection3.High-quality polyolefin heat-shrinkable insulation provides complete terminal integrity4.Transparent outer sleeve enables visual inspection of the connection5.Crimp the terminal and then apply heat to permanently seal the connector
  Contacter maintenant
Features: 1. The application force has no concentrated point, the stress is uniform, and it has a good protective effect on the optical cable. 2. Under the premise of not exceeding the lateral compression strength of the optical cable, it has a greater grip on the optical cable and can withstand greater tension.
  Contacter maintenant
ADSS optical cable suspension clamp components: 1.Aluminum clamp:made of corrosion-resistant aluminum alloy pressure casting, the aluminum alloy has stable chemical properties, good atmospheric corrosion resistance and good mechanical properties. 2.Rubber clamp:Composed of high-quality rubber and center reinforcement, it has the properties of ozone resistance, chemical resistance, weather resistance, high and low temperature performance, high strength and elasticity, and small compression deformation. 3.Bolts, flat washers, spring washers, nuts, closed pins, U-shaped hanging rin
  Contacter maintenant
The preformed strain clamp is used to bear full tension on the bare conductors and overhead insulated conductors in the power transmission and distribution line, and connect the conductors to the strain tower, which can replace the conventional bolt-type strain clamp and compression type strain Clamps and wedge-shaped strain clamps.Structure composition and material description 1. Non-twisted ring: standard form, suitable for small diameter wires; Stranded ring: suitable for larger diameter wires 2. Color code: starting mark of installation 3. Label: Indicate the
  Contacter maintenant
Material 1. Rubber Clamps Composed of high-quality rubber and center reinforcement, it has the properties of ozone resistance, chemical resistance, weather resistance, high and low temperature performance, high strength and elasticity, and small compression deformation. 2. Aluminum splint It is made of corrosion-resistant aluminum alloy by pressure casting. The aluminum alloy has stable chemical properties, good atmospheric corrosion resistance and good mechanical properties.
  Contacter maintenant
The preformed strain clamp is used to undergo full anxiety on the naked conductors and overhead insulated conductors in the energy transmission and distribution line, and connect the conductors to the stress tower, that could replace the traditional bolt-type stress clamp and compression kind strain clamps and wedge-shaped stress clamps.Structure composition and material description 1. Non-twisted ring: standard form, suitable for small diameter wires; Stranded ring: suitable for larger diameter wires 2. Color code: starting mark of installation 3. Label: Indicate the produ
  Contacter maintenant
Features: a. Even stress distribution, no stress concentration point, can well protect the optical cable. b. Under the premise of not exceeding the lateral compression strength of the optical cable, it has a greater grip on the optical cable and can withstand greater tension. c. The grip strength of the optical cable is not less than: 95% of the ultimate tensile strength (UTS) of the optical cable, which is fully suitable for the needs of optical cable erectionProduct composition diagramProduct technical specification sheet:  Sn Model No.
  Contacter maintenant
OPGW Optical Cable Tension Fitting StringFeatures:a. Even stress distribution, no stress concentration point, can well protect the optical cable.b. Under the premise of not exceeding the lateral compression strength of the optical cable, it has a greater grip on the optical cable and can withstand greater tension.c. The grip strength of the optical cable is not less than: 95% of the ultimate tensile strength (UTS) of the optical cable, which is completely suitable for the needs of optical cable erection. Schematic diagram of product composition:Technical specification sheet
  Contacter maintenant
The preformed tension clamp for the conductor is connected to the tower by its matching fittings, such as insert ring, bowl-head hanging plate, etc., which can replace conventional bolt-type tension clamps, compression-type tension clamps and wedge-type tension cables folder.Structure composition and material description 1. Non-twisted ring: standard form, suitable for small diameter wires; Stranded ring: suitable for larger diameter wires 2. Color code: starting mark of installation 3. Label: Indicate the product model 4. Pre-twisted wire: aluminum-clad stee
  Contacter maintenant
The preformed helical guy grip clamp for the conductor is hooked up to the tower by means of its matching fittings, along with insert ring, bowl-head striking plate, and so forth., that could replace conventional bolt-type tension clamps, compression-type anxiety clamps and wedge-type anxiety cables folder.Structure composition and material description 1. Non-twisted ring: standard form, suitable for small diameter wires; Stranded ring: suitable for larger diameter wires 2. Color code: starting mark of installation 3. Label: Indicate the product model 4. Pre-twisted wi
  Contacter maintenant
1. Material: high-quality steel, good electrical conductivity, fast heat dissipation and high temperature resistance.2. Treatment: Advanced technology, hot-forged forming without burrs, smooth surface.3. Strict quality inspection, factory direct sales, quality assurance.Model No.: QH-7Tension strength: 70KNThe main dimensions of the PH extension link meets the requirements of the following figure and table:The meanings of letters and numbers in the models in the table are: number--nominal failure load mark.
  Contacter maintenant
Tie rods is supplied with four full nuts. The material of the rods is steel, strength grade designation 4.6 and meet the requirements for mechanical properties.
  Contacter maintenant
Hook bolt made of Q235B galvanized steel, with good high strength mechanical strength, long term usage in optical fiber cable installation, FTTH networks and aerial ADSS accessories.Technical property:1. performance class:4.6 2. The nominal tensile strength of the bolt material reaches 400Mpa3. The yield ratio of the bolt material is: 0.64. The nominal yield strength of the bolt material is up to 400×0.6=240MPa 
  Contacter maintenant
Outer wire length: 1100, 1200, 1300mm Applicable range: within 120m Large fiber optic cable outer diameter: 16mm Grip strength of wire clamp: 10-30KNTensile strength: 50KN Scope of application: ADSS optical cable Components: guy grip wire, thimble clevis, U-shaped hanging ring, extension ring, nut, bolt, closed pin, etc. Features: light, simple structure, easy to install. Conditions of use: Used for fiber optic cable projects with a span of less than 150m, a line turning angle (elevation angle)> 15o, and a cable ultimate tensile strength (UTS) less than 15
  Contacter maintenant
Details and characteristics of strain clamps: 1.U shackle: hot-dip galvanized cast steel U-shaped hanging ring, which is used to connect with the pole tower fastener. 2.Insert ring: Hot-dip galvanized precision cast steel insert ring, which is embedded in the bending head of the U-shaped hanging ring of the tension clamp, which can protect the tension clamp and connect with the extension rod. 3.PD hanging plate: The hot-dip galvanized precision cast steel PD hanging plate is used to connect the embedded ring and the U-shaped hanging ring, and avoid the optical cable at the exit
  Contacter maintenant
The structure of the preformed armor rod and the short protective rod is simple. A set of pre-twisted wires form an empty tube, which generates a gripping force when wrapping the wire, thereby protecting the wire. The pre-twisted wire protection line is used for vibration protection and has been included in the hardware products.
  Contacter maintenant
Features: 1.The product has been treated with hot-dip galvanizing and has good outdoor anti-corrosion performance. 2.According to the requirements of different optical cables, products that ensure that the optical cable is smaller than the bending radius can be designed. 3.It is convenient to install the pole and tower, the installation is firm, and the optical cable can be well protected to avoid the optical cable from wearing. Purpose: It is used to place the surplus optical cable when the optical cable is connected.
  Contacter maintenant
The transformer bracing cross arm is the cross of dimension of 550x50x50x6mm。The cross arm is hot dipped galvanized.All steel members and other parts of fabricated material as delivered is free of warps, local deformation.Bending of flat strap is carried out cold.About surface treatment:All galvanizing is carried out by the hot dip process. The zinc coating is smooth, continuous and uniform. It is free from acid spot and shall not scale, blister or be removable by handling or packing.
  Contacter maintenant
The c-type hook is used as an accessory for outdoor or indoor wall fiber access. The main purpose is to form an anchor on the wall for the erection and support of the fiber.
  Contacter maintenant
The protective rod is divided into FYB and FYH types.
  Contacter maintenant
NLL wedge-shaped tension clamp body is made of high-strength aluminum alloy; the outer shell is smooth and has a long service life; it is easy to install and use; it has no power loss and is an energy-saving certified product.Features:1. Model : wedge type2. Material: high strength alloy aluminum3. Model No.: NLL-34. U bolt number: 3 nos5. Tension strength: 60kN Technical specification: Model1KV Overhead Insulated wire10KV Overhead Insulated wireWire clamping rangeφ (mm)U-boltNominal failure loadNumberdiameterNLL-125~7010~255.0~10.02M1240NLL-250~120
  Contacter maintenant
Alloy aluminum anchoring bracket CS1500 is a kind of fixed clamp for cable poles, made of cast aluminum alloy. The aluminum alloy telegraph pole bracket produced by our company has a smooth and flat surface, rounded and smooth corners, flat and no roughness, fine workmanship, and durability. Features:1. Breaking load: 10kN2. Package:50 pieces3. Gross weight: 10 kg4. Dimension: 47×31×17cm5. Material: high strength alloy aluminum 
  Contacter maintenant
Relate News
Features of Transmission Line OPGW Tension SetA. the stress distribution is uniform and there can be no pressure focus factor, that can protect the optical cable well.B. beneath the concept of now not exceeding the lateral compression electricity of the optical cable, it has a greater grip at the optical cable and can resist more tension.C. the grip energy of the optical cable isn't always much less than: 90 5% of the last tensile energy (uts) of the optical cable, that is clearly suitable for the wishes of optical cable erection.
We finished the HDG angle cross arm and arranged shipment in May of 2019 to our customers from Tanzania. 
Characteristics of PET Packing Tape(1) Sturdy tensile energy, not most effective has the tensile power of metal strip, but additionally has the ductility of effect resistance, that may ensure the transportation safety of merchandise. (2) Small elongation, elongation is most effective one-sixth of the polypropylene belt, can hold the anxiety for a long time. (3)Robust temperature resistance, melting point of 260 stages, a hundred and twenty degrees under the use of non-deformation. (4) Top security, no metal rust pollutants of the sure gadgets, vivid shade can be used for referen
Power fittings are accessories made of metal materials that are often used for power output. These accessories are of various types, and the shape and size of each part are different, but they play a very important role. Even very small parts will be indispensable, helping people to output electricity. Some of our common metal rings or metal clips, as well as connecting rings that can be connected to metal pipes, belong to the category of fittings.
We clean our workshop on time and keep our workers workings in a clean, comfortable and organized place. 
The tension clamp is deployed at a ordinary time. the current within the circuit is deployed from one end of the electricity supply, and the electrical putting gadget is deployed returned to the opposite end of the strength supply to form a closed circuit. if the present day circuit is blocked, the disconnection may arise due to some purpose. the modern-day within the circuit is not smooth, and the circuit does no longer form a closed loop. this is called an open circuit. therefore, all components need to be freed from hysteresis loss.
Wonderful anti-pressure ability, accurate brief-circuit current ability ;Match with ordinary floor cord l undertake stainless-steel pipe production generation, the pipe is full of water-blocking off compounds, the application version can efficaciously protect the optical fiber ;Using stainless steel tube production technology, the tube filled with water-blocking compounds, can effectively protect the optical fiber;The utility model has the dual functions of a ground wire and a communication optical cable, and avoids the huge cost of repeated erection and maintenance;It is installed on the top
After finishing products, before packing, we put our products in very tidy way so that the quantity never be shortage when customers received the items. 
The hoop is used to restore the metal strand or cord on the pole, and the pull is much like solving to the wall or other objects to tighten the steel strand. There are numerous styles of hoops, cable hoops, telegraph pole hoops, cable hoops, cable hoops, and stainless-steel hoops are extra usually used.Cement poles can be divided into rectangular, octagonal, i-formed, circular or a few different particular-common go-section poles in step with their cross-sections. amongst them, the extra generally used are spherical bolstered concrete poles.
With the continuous growth of China's national economy as a whole and the influence of the reform of telecommunications system, the market demand for ADSS power optical cable has increased significantly, reaching 10 million core kilometers in 2001.In the 21st century, there were several situations at that time: (1) Domestic optical cable enterprises were affected by the "bubble" of optical network, and the telecom market shrank, and the supply exceeded demand.
Optical cable joint box, ADSS optical cable joint box, OPGW optical cable joint box, OPPC optical cable joint box Uses: Widely used in ADSS, OPGW special optical cable joints and the junction of different optical cables, and play a role in protecting optical cable joints. Features: 1.The metal splice box is made of aluminum alloy casting, which is especially suitable for the protection of optical cable joints under high-voltage electric fields. 2.The metal splice box overcomes the weakness of the plastic splice box, which is poor in anti-aging ability and short life under t
Electricity is the most indispensable energy source in our lives. Without it, our lives will fall into a mess, and it is the high-voltage wires that ensure that the electric energy reaches our living places safely. In the past, when technology was not so advanced, wires were pulled from the sky to every household, so many small counties still have many cables between houses. In cities, more are buried underground, which can be more secure. However, in many heavy industrial areas, high-voltage wires still need to be passed through high-altitude.