Hook Bolt For ABC Cable-manufacture,factory,supplier from China

(Total 24 Products for Hook Bolt For ABC Cable)
Hook bolt made of Q235B galvanized steel, with good high strength mechanical strength, long term usage in optical fiber cable installation, FTTH networks and aerial ADSS accessories.Technical property:1. performance class:4.6 2. The nominal tensile strength of the bolt material reaches 400Mpa3. The yield ratio of the bolt material is: 0.64. The nominal yield strength of the bolt material is up to 400×0.6=240MPa 
  Contacter maintenant
Pigtail Bolt M16 used on wooden, concrete and other power poles for supporting clamps and at the consumer’s premises. The clamps corrosion resistance conforms to the standards.Bolts and nuts is made of hot dip galvanised steel. Ultimate Tensile strength (UTS) of the clamp is 20KN.
  Contacter maintenant
The suspension support hook clamp made of hot dip galvanized steel, the dimension is 120mm (L)and 10mm as diameter of the hook. There is one hole of M14 punched on the base plate. The thickness of the base plate is 3.2mm. 
  Contacter maintenant
Eye bolts is manufactured from steel, strength designation 4.6 and meet the requirements for mechanical properties.The safe working load of any eye bolt is that load which may be safely carried in an axial direction.
  Contacter maintenant
The JJ-3 insulation piercing clamp has a main line cross-section of 16-95mm, a branch cross-section of 1.5-10mm, an applicable voltage of 1KV, and a nominal current carrying capacity of 138. It has the characteristics of long service life, high conductivity, and firm wiring. Features:1. Simple installation: puncture structure, no need to strip the wire, torque nut, constant puncture pressure. 2. Thickened shell: Nylon material is used to ensure that it can bear enough pressure.3.
  Contacter maintenant
The JJ-3 insulation piercing clamp has a main line cross-section of 16-95mm, a branch cross-section of 1.5-10mm, an applicable voltage of 1KV, and a nominal current carrying capacity of 138. It has the characteristics of long service life, high conductivity, and firm wiring.Features: 1. Simple installation: puncture structure, no need to strip the wire, torque nut, constant puncture pressure.2. Thickened shell: Nylon material is used to ensure that it can bear enough pressure.3.
  Contacter maintenant
Square flat washer with 17.5mm diameter hole for 5/8" diameter bolt. Galvanized per ASTM A-153.Features:1. Material: steel2. Finish: galvanized3. Usage: for 5/8” bolts. Technical specification: 
  Contacter maintenant
The bolt can be threaded for total length as per customers' requirement.
  Contacter maintenant
U bolt has high strength and corrosion resistance and is widely used in power industry.Features:1. Carbon steel material, corrosion resistance, high hardness, not easy to deform2. Hot dip galvanized zinc coating for increased corrosion resistance and longer life3. The thread & pitch can be made according to different standard 
  Contacter maintenant
The c-type hook is used as an accessory for outdoor or indoor wall fiber access. The main purpose is to form an anchor on the wall for the erection and support of the fiber.
  Contacter maintenant
The mounting hook clamp are used on poles such as telegraph poles or cylindrical poles. The main purpose is to form an anchor point and erect an optical fiber line body. The finish is hot-dip galvanized, which is corrosion-resistant and anti-rust. The two sides are transparent, equipped with stainless steel fastening strips, which are firm, stable and beautiful after installation.Usage: Used with 12-20mm steel belt, fixed on the pole.Material: carbon steelDimension:65×65×54mm(L×W×H).Installation image: 
  Contacter maintenant
PVC insulation piercing connector It is suitable for the branching and splicing of overhead insulated wires of 1kV and below. Features:Fully insulated housingStructure sealed, waterproof, anti-corrosion, long lifePuncture structure, torque bolt, ensure puncture pressureDifferent diameter and different wire connection, strong applicability.Model No.Suitable conductor range sqmmMain dimensionsqmmNormal current(A)Bolt noMain lineSub lineABHJBC1/7010-7015-10412355551JBC1/9516-951.5-10412655551JBC-116-12016-1206049802991JBC-250-24050-2407484.51164762
  Contacter maintenant
The Bolts, eye bolts, eye nuts and Nuts is manufactured by Hot/Cold forging process neatly and cleanly finished and have metric threads.Eye bolts threads is throughout their length and bolts threads is at 60% of their length.All the materials have bright surface finish. composition:1.The plain washers is cold punched2.Individual nuts and eye nut is used for special purposes, such as lock nuts.3.Before dispatch from the works one washer is fitted to each bolt, eye bolt, eye nut and a nut is screwed on the whole threaded length and left in this position.4.Each set of bolt and nut includes o
  Contacter maintenant
TJ brass bolts are suitable for connection in power transmission and distribution lines. The red copper material has good electrical conductivity and high resistance to electrical resistance. The bolt design guarantees constant contact pressure; the surface is smooth, without burrs, making the work more stable and calm.
  Contacter maintenant
Insulation strain clamp PAL2000 is used for overhead ABC cable, aluminum alloy main body, nylon PA66 insulation core, stainless steel wire rope. The wedge-shaped insulated aluminum alloy tension clamp produced by our company has a variety of specifications. PAL2000 is used for cables with a diameter of 70sqmm to 150sqmm and a tensile load of 15KN. The length of the wire rope can be customized, and the batch quantity can be printed on the product according to customer needs . Features:1. Material: high strength aluminum alloy.
  Contacter maintenant
Cable wall mounted anchoring clamp with ScrewsMaterial: hot dip galvanized steelOur clamp anchoring bracket with the advantages below:1. Reduce cable maintenance expenses, avoid frequent repairs, save operating costs, and users get a better experience. 2. The FTTH technology has been widely used, the construction speed is also very fast, and the technical risk is low.3. It provides a stable and reliable guarantee for fiber to the home, and the efficiency of network usage is improved.
  Contacter maintenant
The c type hook clamp is used as an accessory for outdoor or indoor wall fiber access. The main purpose is to form an anchor on the wall for the erection and support of the fiber. The hanging part rotates more than 180 degrees, so the wire It can only fall off manually, and the wire will not be unhooked even in a strong wind environment.
  Contacter maintenant
The NLL wedge-shaped strain clamp has the advantages of very small hysteresis loss, light weight, and convenient installation, which meets the requirements of energy saving and consumption reduction in the transformation of the national grid. The main body of the product is made of aluminum alloy, and the bolts and nuts are made of hot-dip galvanized material.Features:1. Model : wedge type2. Material: high strength alloy aluminum3. Model No.: NLL-24. U bolt number: 2 nos M125. Tension strength: 50kNTechnical specification: Model1KV Overhead Insulated wir
  Contacter maintenant
Power equipment optical cable communication 4D type protective hardware anti-vibration hammer with armor rod. Features: Due to the use of hammers with different sizes and masses, the response frequency range of traditional shock-proof hammers is expanded. Because the shapes of large and small hammers and hooks have no edges and corners, corona is reduced. In addition, the use of aluminum alloy for the hook can also reduce the energy loss of the wire.
  Contacter maintenant
Features: 1.The product has been treated with hot-dip galvanizing and has good outdoor anti-corrosion performance. 2.According to the requirements of different optical cables, products that ensure that the optical cable is smaller than the bending radius can be designed. 3.It is convenient to install the pole and tower, the installation is firm, and the optical cable can be well protected to avoid the optical cable from wearing. Purpose: It is used to place the surplus optical cable when the optical cable is connected.
  Contacter maintenant
The hook of the parallel cable clamp can be rotated and fixed at ninety degrees. It is used to fix the optical cable wire, fasten it on the steel strand, and connect and fix the S-shaped fixing member on the steel strand.  The stranded stay wire is 2.0mm*7 & 2.2mm*7.Dimension : 50×31.5×80mm(L×W×H)Installation image: Drawing: 
  Contacter maintenant
The cable tie is able to loop and lock fully. Extra tie material left past the lock to prevent pull through. Self-locking design for fast and secure installation provided.The cable tie have maximum diameter capable of bundling two to four service wires and cables with cross-section in the range of 4-25mm2. 
  Contacter maintenant
The surplus cable rack is used to suspend and fix the surplus OPGW optical cable and ADSS optical cable on the tower in the overhead line for maintenance and inspection. 1.The remaining cable rack for poles is fixed on the poles by two sets of steel band hoops 2. The remaining cable frame for the tower is fixed on the iron tower angle steel by two sets of right-angle splints.Purpose: It is used to place the surplus optical cable when the optical cable is connected.
  Contacter maintenant
OPGW Optical Cable Tension Fitting StringFeatures:a. Even stress distribution, no stress concentration point, can well protect the optical cable.b. Under the premise of not exceeding the lateral compression strength of the optical cable, it has a greater grip on the optical cable and can withstand greater tension.c. The grip strength of the optical cable is not less than: 95% of the ultimate tensile strength (UTS) of the optical cable, which is completely suitable for the needs of optical cable erection. Schematic diagram of product composition:Technical specification sheet
  Contacter maintenant
Relate News
Wonderful anti-pressure ability, accurate brief-circuit current ability ;Match with ordinary floor cord l undertake stainless-steel pipe production generation, the pipe is full of water-blocking off compounds, the application version can efficaciously protect the optical fiber ;Using stainless steel tube production technology, the tube filled with water-blocking compounds, can effectively protect the optical fiber;The utility model has the dual functions of a ground wire and a communication optical cable, and avoids the huge cost of repeated erection and maintenance;It is installed on the top
Wires mainly include bare wires, electromagnetic wires, insulated wires, power cables, communication cables and optical cables for electrical appliances. Electric cable refers to the materials used for power, communication and related transmission purposes. There is no strict boundary between "wire" and "cable".
Tools/raw materials Aluminum alloy joint box Pre-twisted suspension clamp Optical cable down lead clamp Cable rack Tower fastener Cable hoop Whip and hammer Pre-twisted hardware1.Before installing the inner twisted wire, pass the outer twisted wire through the embedded ring and make it parallel to the optical cable, and mark the optical cable where the outer twisted wire is colored.2.Winding the first group of inner twisted wires on the optical cable; Align the second group of inner twisted wires with the first group of inner twisted wires, winding the s
Characteristics of PET Packing Tape(1) Sturdy tensile energy, not most effective has the tensile power of metal strip, but additionally has the ductility of effect resistance, that may ensure the transportation safety of merchandise. (2) Small elongation, elongation is most effective one-sixth of the polypropylene belt, can hold the anxiety for a long time. (3)Robust temperature resistance, melting point of 260 stages, a hundred and twenty degrees under the use of non-deformation. (4) Top security, no metal rust pollutants of the sure gadgets, vivid shade can be used for referen
1.1 puncture structure, easy installation, no need to peel insulated wire; 1.2 moment nut, constant puncture pressure, ensure good electrical connection without damaging wire; 1.3 self sealing structure, moisture proof, water proof, corrosion proof, extend The service life of insulated conductors and clamps 1.4 use special contact blade, suitable for copper (aluminum) Butt joint and copper-aluminum transition 1.5 electrical contact resistance is small, contact resistance is less than 1.1 times of resistance of equal length branch wire, dL/T765.1-2001 standard 1.6 speci
With the continuous growth of China's national economy as a whole and the influence of the reform of telecommunications system, the market demand for ADSS power optical cable has increased significantly, reaching 10 million core kilometers in 2001.In the 21st century, there were several situations at that time: (1) Domestic optical cable enterprises were affected by the "bubble" of optical network, and the telecom market shrank, and the supply exceeded demand.
Optical cable joint box, ADSS optical cable joint box, OPGW optical cable joint box, OPPC optical cable joint box Uses: Widely used in ADSS, OPGW special optical cable joints and the junction of different optical cables, and play a role in protecting optical cable joints. Features: 1.The metal splice box is made of aluminum alloy casting, which is especially suitable for the protection of optical cable joints under high-voltage electric fields. 2.The metal splice box overcomes the weakness of the plastic splice box, which is poor in anti-aging ability and short life under t
Power fittings are accessories made of metal materials that are often used for power output. These accessories are of various types, and the shape and size of each part are different, but they play a very important role. Even very small parts will be indispensable, helping people to output electricity. Some of our common metal rings or metal clips, as well as connecting rings that can be connected to metal pipes, belong to the category of fittings.
Identification and use of strain clamp specifications: According to the wire, the general strain clamp can be divided into two types, one is the wire strain clamp, and the other is the optical cable strain clamp. Their appearance is very different and can be easily distinguished.   The wire tension clamp is also called the bolt-type tension clamp (NLD-1). When in use, the vertical pressure of the U-shaped screw and the friction generated by the wavy slot of the wire clamp are used to fix the wire.
1.extensive variety of applications, torsion resistance and pressure resistance, balanced torsion torque, company and tight locking, and huge adjustment variety. 2.put it at the telegraph pole, tighten and fix it. 3. the poles with diameters of one hundred seventy five-197mm can be adjusted. Pole clamp belt for cable garage bracket is manufactured from c201 stainless-steel, with width of 19mm, thickness of 0.7mm and duration from 1.2m to at least one.5m primarily based on exclusive pole.
Features of Transmission Line OPGW Tension SetA. the stress distribution is uniform and there can be no pressure focus factor, that can protect the optical cable well.B. beneath the concept of now not exceeding the lateral compression electricity of the optical cable, it has a greater grip at the optical cable and can resist more tension.C. the grip energy of the optical cable isn't always much less than: 90 5% of the last tensile energy (uts) of the optical cable, that is clearly suitable for the wishes of optical cable erection.
The preformed suspension clamp is used for the connection of various wires such as ADSS optical cable and OPGW optical cable in the linear pole tower.