The plastic fisher screw wall plug is made of high-quality PE material, which has strong fixation and is not easy to rotate. A variety of sizes are available for a wide range of applications. Corrosion-resistant, high-density polyethylene has rigidity, hardness and mechanical strength.
Contacter maintenant
The c-type hook is used as an accessory for outdoor or indoor wall fiber access. The main purpose is to form an anchor on the wall for the erection and support of the fiber.
Contacter maintenant
FTTH drop cable screw eye is a supporting device that is directly screwed to a wooden wall or fixed to a brick-concrete wall with an expansion tube to connect and fix the S fixing member. Cement walls need to be used with expansion plugs.The expansion plug is used in conjunction with the ring hook. It is used as an optical fiber access accessory on the cement wall.
Contacter maintenant
FTTH drop cable fisher screw eye is installed on the bracket, used to connect and fix the S fixing piece. The expansion plug is used in conjunction with the ring hook. It is used as an optical fiber access accessory on the cement wall.
Contacter maintenant
-Impact: No damage on dropping from altitude ≥ 6m to a hard floor-Vibration: Resistance against vibration of standard sine wave, frequency: 20 Hz, Amplitude: ≥ 5mm, duration: 0.5 hour-Material: durable PVC-Color: light gray or white -Temperature: -10°C up to +70°C-Humidity: Up to 100 %.Specification required for different cable diameter ranges:No.ItemUnitSpecification required for different cable diameter ranges (mm)4.0 ~ 6.346.35~ 8.288.5 ~ 11.711.71 ~ 14.314.31 ~ 19.31.1Diametermm9.8-10.39.8-10.310.8-11.312.0-12.912.0-12.91.2Length mm125012501300135016501.3Gripping section lengthmm
Contacter maintenant
The c type hook clamp is used as an accessory for outdoor or indoor wall fiber access. The main purpose is to form an anchor on the wall for the erection and support of the fiber. The hanging part rotates more than 180 degrees, so the wire It can only fall off manually, and the wire will not be unhooked even in a strong wind environment.
Contacter maintenant
The medium and high tension strain clamps are composed of a double-layer twisted wire structure. The tensile inner twisted wire is made of galvanized steel wire or aluminum-clad steel wire. The inner wall of the pre-twisted wire is stuck with a layer of fine emery to increase friction. The pre-twisted wire is preformed into four sub-bundles during processing to avoid installation errors and facilitate quick installation. The ends of the pre-twisted wires are bent radially outward to avoid squeezing and damaging the optical cable.
Contacter maintenant
Cable wall mounted anchoring clamp with ScrewsMaterial: hot dip galvanized steelOur clamp anchoring bracket with the advantages below:1. Reduce cable maintenance expenses, avoid frequent repairs, save operating costs, and users get a better experience. 2. The FTTH technology has been widely used, the construction speed is also very fast, and the technical risk is low.3. It provides a stable and reliable guarantee for fiber to the home, and the efficiency of network usage is improved.
Contacter maintenant
The TC insert ring is made of Magang, which has high strength and toughness, high vibration damping and good elongation. Malleable iron generally refers to malleable cast iron, cast iron with a certain chemical composition into a white blank, and then annealed cast iron, which has higher strength, plasticity and impact toughness, and can partially replace carbon steel. Technical characteristics:Model No.: TC-05Bolt size: M14Tension strength: 50KN
Contacter maintenant
ADSS terminating helix dead end is made of aluminum-clad steel wire, and the pre-twisted wire is preformed into a bundle during processing, and a firm layer of emery is glued to the inner wall to increase the grip of the tension clamp under the condition of reducing the side pressure on the optical cable.
Contacter maintenant
Preformed inner protection line rods:The material is aluminum-clad steel wire, which is the same material as all the aluminum-clad steel wires of OPPC cable. The inner wall of the protector rods is glued with a layer of gold steel sand through a high-strength polymer water-soluble environmentally friendly adhesive to increase the friction with the optical cable. The rods is preformed into four sub-bundles during production, which is convenient for quick installation.
Contacter maintenant
Medium and large tension set are composed of a double-layer twisted wire structure. The tension inner rods is made of galvanized steel wire or aluminum-clad steel wire, and the inner wall of the pre-stranded wire is stuck with a layer of fine emery to increase friction. The inner rods includes 4 groups, during processing in the factory to avoid installation errors and facilitate quick installation. The ends of the pre-twisted wires are bent radially outward to avoid squeezing and damaging the optical cable.
Contacter maintenant
1. The twisting direction of the steel stranded wire and the matching preformed guy grip needs to be the same, and the tensile strength of the galvanized steel wire is 1370N/mm2-1470N/mm2. 2. The white corundum used to increase the friction between the pre-twisted wire and the surface should meet the requirements of GB/T 2479.3. The surface of the preformed guy grip should be smooth and free of defects such as cracks, folds and scars.4. The size and tolerance of the pre-twisted wire The size of the pre-twisted wire should meet the requirements of the design d
Contacter maintenant
Light short span tension set for ADSS cable diameter 11.0-12.0mm, tension strength 4KN, and max span 120 meters.The tension dead end guy grip is made of galvanized steel wire or aluminum-clad steel wire, and the inner wall of the pre-twisted wire is stuck with a layer of fine emery to increase friction.1.The short span ADSS tension set is used for the installation of ADSS cable, includes ADSS guy grip, Galvanized thimble clevis and U shackle. 2. The structure of the short span ADSS guy grip is simple.
Contacter maintenant
Tie rods is supplied with four full nuts. The material of the rods is steel, strength grade designation 4.6 and meet the requirements for mechanical properties.
Contacter maintenant
1. Material: high-quality steel, good electrical conductivity, fast heat dissipation and high temperature resistance.2. Treatment: Advanced technology, hot-forged forming without burrs, smooth surface.3. Strict quality inspection, factory direct sales, quality assurance.Model No.: QH-7Tension strength: 70KNThe main dimensions of the PH extension link meets the requirements of the following figure and table:The meanings of letters and numbers in the models in the table are: number--nominal failure load mark.
Contacter maintenant
ADSS optical fiber cable insulation wedge clamp is a kind of ADSS optical cable clamp. Mainly used for optical cables with 6-9mm cable diameter. The main body material is PA66, stainless steel wire rope, injection molding process, widely used in communication engineering, etc. Large quantities are exported to South America, Southeast Asia and other countries and regions.Features:Dimension: 173×65×40mmUnit weight:190gCarton size: 550×410×250mmQuantity per carton : 100 piecesMaterial: Nylon and stainless steelCable diameter: 6-9mm Installation image:
Contacter maintenant
The pole clamp is suitable for connecting the tension suspension clamp and the electric pole. Features: 1. Product manufacturing is strictly controlled and meets production standards. 2.The surface of the product has no burrs and is relatively smooth. 3. Support customization of a variety of special-shaped productsThe hoop device is composed of a hoop plate, a wing plate, a tie rib plate, a bolt and an inner liner. An embedded hoop, which is formed by joining the left and right halves of the hoop.
Contacter maintenant
The WS-type bowl head hanging plate produced by our company has the characteristics of oxidation resistance, corrosion resistance, and durability. It is suitable for the connection between the insulator string and the fittings, the line clamp and the insulator string, and the lightning protection wire and the pole tower. The main body is made of malleable cast iron, hot-dip galvanized, oxidation-resistant and corrosion-resistant.
Contacter maintenant
PAL1000 aluminum alloy optical cable insulation strain clamp is a product suitable for overhead insulated conductors. The product is used for cable pull, aluminum alloy body material, PA66 insulation core, stainless steel wire rope, and the product process is die-casting. The high-quality aluminum alloy material has strong corrosion resistance and is not easy to rust and age. The appearance is neat and tidy, and the unique design can well protect the cable.Features:1. Material: high strength aluminum alloy.
Contacter maintenant
NLL wedge-shaped tension clamp body is made of high-strength aluminum alloy; the outer shell is smooth and has a long service life; it is easy to install and use; it has no power loss and is an energy-saving certified product.Features:1. Model : wedge type2. Material: high strength alloy aluminum3. Model No.: NLL-34. U bolt number: 3 nos5. Tension strength: 60kN Technical specification: Model1KV Overhead Insulated wire10KV Overhead Insulated wireWire clamping rangeφ (mm)U-boltNominal failure loadNumberdiameterNLL-125~7010~255.0~10.02M1240NLL-250~120
Contacter maintenant
Alloy aluminum anchoring bracket CS1500 is a kind of fixed clamp for cable poles, made of cast aluminum alloy. The aluminum alloy telegraph pole bracket produced by our company has a smooth and flat surface, rounded and smooth corners, flat and no roughness, fine workmanship, and durability. Features:1. Breaking load: 10kN2. Package:50 pieces3. Gross weight: 10 kg4. Dimension: 47×31×17cm5. Material: high strength alloy aluminum
Contacter maintenant
Insulation strain clamp PAL2000 is used for overhead ABC cable, aluminum alloy main body, nylon PA66 insulation core, stainless steel wire rope. The wedge-shaped insulated aluminum alloy tension clamp produced by our company has a variety of specifications. PAL2000 is used for cables with a diameter of 70sqmm to 150sqmm and a tensile load of 15KN. The length of the wire rope can be customized, and the batch quantity can be printed on the product according to customer needs . Features:1. Material: high strength aluminum alloy.
Contacter maintenant
The PA2000 FTTH plastic tension clamp is designed to anchor insulated service lines with 2 conductors to the pole. The clamp is composed of a body, wedges and removable, adjustable bail. One core adjustable anchor clamp are designed to supporting the neutral messenger, the wedge can be self-adjusted.Features:Unit weight:550gCarton size: 550×410×250mmQuantity per carton : 50 piecesMaterial: Nylon and stainless steelCable diameter: 12-15mmTension strength: 7KNDrawing:
Contacter maintenant