Side Tie Insulator Helical Plastic-manufacture,factory,supplier from China

(Total 24 Products for Side Tie Insulator Helical Plastic)
The energy distribution top tie can be used to fix naked or insulated wires inside the top grooves of pin insulators and submit insulators of the power distribution device.
  Contacter maintenant
The plastic fisher screw wall plug is made of high-quality PE material, which has strong fixation and is not easy to rotate. A variety of sizes are available for a wide range of applications. Corrosion-resistant, high-density polyethylene has rigidity, hardness and mechanical strength.
  Contacter maintenant
The power distribution cable tie is equipped with rubber pads to provide anti-wear function. The state line is not equipped with rubber pads and is not sandblasted. Since there are rubber pads to provide buffering around the wire, the abrasion of the contact surface between the wire and the insulator is avoided. Therefore, the power distribution cable can provide better protection to the wires, and the installation is easier and faster.
  Contacter maintenant
The top tie are all designed in a spiral structure and include aluminum-clad steel wires. the central part of the energy distribution cable is fashioned in the factory, and its form may be matched with diverse insulators and wires.
  Contacter maintenant
The power distribution top tie can be used to fix bare or insulated wires in the top grooves of pin insulators and post insulators of the power distribution system.
  Contacter maintenant
The strength distribution cable is equipped with rubber pads to offer anti-put on characteristic. the state line is not geared up with rubber pads and isn't sandblasted. due to the fact that there are rubber pads to provide buffering around the cord, the abrasion of the touch floor between the wire and the insulator is prevented. therefore, the energy distribution cable can provide better safety to the wires, and the installation is less difficult and faster.
  Contacter maintenant
The cable tie is able to loop and lock fully. Extra tie material left past the lock to prevent pull through. Self-locking design for fast and secure installation provided.The cable tie have maximum diameter capable of bundling two to four service wires and cables with cross-section in the range of 4-25mm2. 
  Contacter maintenant
The tie strap is used for tying 11kV or 33kV cross-arms to poles. There are steel galvanized bolts and nuts assembled.  All ferrous part is made in hot dip galvanized.
  Contacter maintenant
The preformed top tie are all designed in a spiral structure and consist of two aluminum-clad steel wires. The central part of the power distribution cable is formed in the factory, and its shape can be matched with various insulators and wires.
  Contacter maintenant
1.Polymer Insulator Character:1.1high mechanical strength;1.2Good performance of hydrophobicity and anti-pollution;1.3 Excellent electrical Performance;1.4 small volume and lightweight. Type of productsOur products cover 10KV-1100KV high-voltage and extra-high voltage hollow ceramic insulators.Which include GIS outlet line insulator shellSF6 circuit breaker insulator shellCombined current and potential transformer insulator shell.capacitor insulator shellcable terminal insulator shellarrester insulator shell and solid pillar insulatorfuse protector insulatortank capacitor outlet line casi
  Contacter maintenant
The S drop cable clamp is made of stainless steel rope and flame-retardant ABS plastic body, one head with a round steel wire, used to bind the self-supporting drop cable suspension wire, and hang the optical cable on the supporting device.Dimension:135×23.5×17.5mm(L×W×H).Instruction: Wrap the 2-6mm optical brazing wire in the cylindrical groove of the S part, and fix the optical brazing wire connecting rod.Packing: plastic bag first then come in a resistant biodegradable cardboard box with the customer information in the visible part of the box. Installation image: 
  Contacter maintenant
1.Product name: tooth-shaped stainless steel cable tie buckle 2.Material: 316/304 stainless steel, with good and corrosion resistance.
  Contacter maintenant
The preformed helical guy grip clamp for the conductor is hooked up to the tower by means of its matching fittings, along with insert ring, bowl-head striking plate, and so forth., that could replace conventional bolt-type tension clamps, compression-type anxiety clamps and wedge-type anxiety cables folder.Structure composition and material description 1. Non-twisted ring: standard form, suitable for small diameter wires; Stranded ring: suitable for larger diameter wires 2. Color code: starting mark of installation 3. Label: Indicate the product model 4. Pre-twisted wi
  Contacter maintenant
1.The short span ADSS helical guy grip is used for 10.6-11.6mm ADSS cable, with approximate length 940mm±30mm, or customize based on requirements of customers.2.The structure of the short span ADSS guy grip is simple installation, with strong grip once the tubular structure naturally wound on the ADSS cable. 3.The short span ADSS helical guy grip has reliable performance, made of aluminum-clad steel.Using tips1.Due to the special structure of guy grip, only be used once after being stressed, and cannot be reused. 2.The specification and model of the guy grip must be provided when an
  Contacter maintenant
The stainless steel buckle with Strong load-bearing capacity, tight binding force, no slipping, no tripping, suitable for bundling various types of large-scale, hanging, and vertical heavy objects. Features:-Buckles with rounded edges-With a toothed cavity for better grip of the steel tape-Flat body for fastening to the steel tape-With fins for maximum tension and fixed and secure grip of the steel tape-The buckle is for ¾-inch steel strapping tape.Packaging:The buckles packaging in plastic bags of 100 units and these in turn in cardboard boxes adequately protected against damage or humid
  Contacter maintenant
Nylon cable ties are made of UL-approved nylon-66 (Nylon 66) by injection molding, with a fire rating of 94V-2. They have good acid resistance, corrosion resistance, insulation, resistance to aging, and strong endurance. The operating temperature is -20°C to +80°C (normal nylon 66). Nylon cable ties have high tensile strength, impact resistance, and strong acid and alkali resistance.
  Contacter maintenant
The adaptor socket clevis W-7B is mainly used to connect the suspension clamp and the insulator string, and cooperate with other accessories to connect the wires and insulate. ALL WELL W-7B has high mechanical strength, is not easy to produce cracks, has good structural stability, the product is not easy to age, and the surface is polished and polished without burrs. In the transmission line, the bowl head hanging board W-7B plays the role of hanging the insulator string and the suspension clamp, and bears greater working stress.
  Contacter maintenant
Steel belt 20X0.7mm with buckle, tts strength and ductility meet requirements for bending the different size of cables on poles. Steel Buckle can hold a single or double wrapped band configuration.Packing:Steel roll of 50 m is packed in form of closed reel rewind tape in nylon plastic roll.
  Contacter maintenant
Dead end clamp is made of plastic body with very high mechanical and climatic resistance. A stainless steel flexible cord equipped with movable insulating saddle and two sleeves compressed on the ends to prevent detachment from the clamp body.An inner sheath consisting of two insulating plastic wedges for clamping of the neutral carrier without damaging the cable insulation.
  Contacter maintenant
Dimensions:Height: 545±5mm.Min Dry Aring Distance:350mm. Min Creepage Distance:900mmDiameter Of The Rod:Φ17mm.Coupling Dimensions: Single Ear/ Binaural.Number Of Sheds: 8. Raw Materials:1.End-Fitting:1.1Material:    Socket: Cast Iron Or Cast Steel, Hot Dip Galvanized.    Ball: Forged Steel, Hot Dip Galvanized.1.2 Minimum Thickness Of The Galvanization:86um.2.Core:2.1 Material: Epoxy& Glass Fiber, Acid-Resistant Type.2.2 Diamter:Φ17mm.3.
  Contacter maintenant
The socket clevis W-7A is the connection fitting in the power fittings. In the transmission line, the Wantou Hanging Board W-7A plays the role of suspending the insulator string and the suspension clamp, and bears greater working stress. Its safety performance is very important to the transmission line. The Wantou Hanging Board is in the construction of the power grid.
  Contacter maintenant
Tie rods is supplied with four full nuts. The material of the rods is steel, strength grade designation 4.6 and meet the requirements for mechanical properties.
  Contacter maintenant
Transmission line fitting socket tongue is suitable for connecting suspension insulator strings between overhead power lines and substations. In the transmission line, the bowl head hanging plate plays the role of hanging the insulator string and the suspension clamp, and bears greater working stress.Features: 1. Cast, hot-dip galvanized.2. Connection mark 16; 20; 24.3. Equipped with W pins, the pins are stainless steel or bronze.
  Contacter maintenant
Tension insulators are used for transmission and distribution lines and communication lines, broadcast line terminals, corners or large-span poles, The balance pole is subjected to tensile stress. When in use, the wire and the pull wire pass through the hole and slot, and the tension wire is used for insulation and connection.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: M16×1830mm4. Finish: hot dip galvanized 
  Contacter maintenant
Relate News
1. Get rid of the dirt at the surface of the helical useless quit , after which uniformly coat a floor of the electrical strength fitting with a coating for growing the toughness and flexibility of the suitable;2. Coating a layer of epoxy resin on the proper, and laying a layer of glass fabric before the epoxy resin is solidified;3. Apply two layers of epoxy resin at the floor of the glass material with the glass fabric. after the 2 layers of epoxy resin are solidified, apply 3 layers of epoxy resin and lay  layers of glass cloth earlier than the 3 layers of epoxy resin are solidified.
The software model pertains to a clip, in particular to a clip for without difficulty striking the clip. in current workplace area, workplace desks are typically separated with the aid of a partition panel, that is usually made up of plastic troughs, glass and fiberboard, which gives the body of workers a quiet, unfastened office space.
Optical cable joint box, ADSS optical cable joint box, OPGW optical cable joint box, OPPC optical cable joint box Uses: Widely used in ADSS, OPGW special optical cable joints and the junction of different optical cables, and play a role in protecting optical cable joints. Features: 1.The metal splice box is made of aluminum alloy casting, which is especially suitable for the protection of optical cable joints under high-voltage electric fields. 2.The metal splice box overcomes the weakness of the plastic splice box, which is poor in anti-aging ability and short life under t
After finishing products, before packing, we put our products in very tidy way so that the quantity never be shortage when customers received the items. 
We finished the HDG angle cross arm and arranged shipment in May of 2019 to our customers from Tanzania. 
We clean our workshop on time and keep our workers workings in a clean, comfortable and organized place. 
Characteristics of PET Packing Tape(1) Sturdy tensile energy, not most effective has the tensile power of metal strip, but additionally has the ductility of effect resistance, that may ensure the transportation safety of merchandise. (2) Small elongation, elongation is most effective one-sixth of the polypropylene belt, can hold the anxiety for a long time. (3)Robust temperature resistance, melting point of 260 stages, a hundred and twenty degrees under the use of non-deformation. (4) Top security, no metal rust pollutants of the sure gadgets, vivid shade can be used for referen
Power fittings are accessories made of metal materials that are often used for power output. These accessories are of various types, and the shape and size of each part are different, but they play a very important role. Even very small parts will be indispensable, helping people to output electricity. Some of our common metal rings or metal clips, as well as connecting rings that can be connected to metal pipes, belong to the category of fittings.
The tension clamp is deployed at a ordinary time. the current within the circuit is deployed from one end of the electricity supply, and the electrical putting gadget is deployed returned to the opposite end of the strength supply to form a closed circuit. if the present day circuit is blocked, the disconnection may arise due to some purpose. the modern-day within the circuit is not smooth, and the circuit does no longer form a closed loop. this is called an open circuit. therefore, all components need to be freed from hysteresis loss.
Wonderful anti-pressure ability, accurate brief-circuit current ability ;Match with ordinary floor cord l undertake stainless-steel pipe production generation, the pipe is full of water-blocking off compounds, the application version can efficaciously protect the optical fiber ;Using stainless steel tube production technology, the tube filled with water-blocking compounds, can effectively protect the optical fiber;The utility model has the dual functions of a ground wire and a communication optical cable, and avoids the huge cost of repeated erection and maintenance;It is installed on the top
The standard plywood crates customized based on requirements of customers and loaded in the container.
Electricity is the most indispensable energy source in our lives. Without it, our lives will fall into a mess, and it is the high-voltage wires that ensure that the electric energy reaches our living places safely. In the past, when technology was not so advanced, wires were pulled from the sky to every household, so many small counties still have many cables between houses. In cities, more are buried underground, which can be more secure. However, in many heavy industrial areas, high-voltage wires still need to be passed through high-altitude.